help needed on my note acceptor

egan79 · Post by **egan79** » Tue Jul 30, 2013 11:11 pm

hi need a little help i have a warped fruit machine 2006 with eclipse onestop mpu board.the problem is when i turn the machine on it comes up with bnv???? i have entered the bnv code and its come up with key valid.its set up the note on the screen were the bank and credits are and the hopper level as changed from £125 to £250 i have fooled the machine by pressing the hopper top up so it thinks the hopper is full as i thought this might be part of the problem.but all i get is a solid red X led light on the front of the note display the wireing seems all ok as far as i can tell when i turn the machine on it comes up with cc/talk or something like that the note machine is a lumina upgraded to v25 it says on it.could this be broken or just doing something wrong its doing my head in

buzzer · Post by **buzzer** » Wed Jul 31, 2013 1:10 pm

lumina note acceptors are garbage m8..

can u get it to accept a note on test?
you may have to turn a dil switch on (don't know which one) to enable the note acceptor in real time play...

egan79 · Post by **egan79** » Wed Jul 31, 2013 10:18 pm

if you mean demo mode then yes i have tryed its still the same just looking at the front of the note accepter theres a red light a red x led light.i have turned dil switch 8 on the mpu board as i think thats the one that communicates with it there is a set of dils on the lumina its self 1to8 dil 2 and 7 is on as thats what it was when i got the machine i have turned others on but no look and just put the dill 2 and 7 back on

egan79 · Post by **egan79** » Wed Jul 31, 2013 10:21 pm

not sure if i should just buy a new note acceptor not sure what one?or if iam just not doing something correct

buzzer · Post by **buzzer** » Wed Jul 31, 2013 11:04 pm

try this:
reset machine and input bnv key

if it says bnv valid, then switch machine off/on and go into test mode

there will either be a note acceptor test or note acceptor will be tested through "coin in" test.

if you cannot get the note acceptor to work on test, then you will have a faulty note acceptor...

if the note acceptor does work on test, then it is a dil switch setting that is wrong...

egan79 · Post by **egan79** » Thu Aug 01, 2013 9:51 pm

thanks i will try it makes me think theres a problem with it as there a solid red led light on the note accepter and when i look it up it means memory corrupted aslo if its faulty what new note acceptor will i need to buy?

buzzer · Post by **buzzer** » Thu Aug 01, 2013 10:02 pm

if its faulty you will be looking for a new lumina, unless you can change the bracket and loom

egan79 · Post by **egan79** » Thu Aug 01, 2013 10:50 pm

thanks buzzer for your help sound daft but what are loom is that the wireing

buzzer · Post by **buzzer** » Fri Aug 02, 2013 7:36 pm

yes m8..

loom = wiring..

egan79 · Post by **egan79** » Sat Aug 03, 2013 5:17 pm

looks like the note acceptor is broke tryed it on test mode and still would not take notes bnv says key valid

buzzer · Post by **buzzer** » Sat Aug 03, 2013 6:06 pm

what is the bnv code your entering?

is it 123456 or something else?

and what type of coin mech mech does it have?

seriel/ parallel/ c-c talk?

the reason i ask is that switch setting 6 off, 7 on, 8 off is for c-c talk mode.

are you resettiing note acceptor before inputing key?

egan79 · Post by **egan79** » Sat Aug 03, 2013 8:12 pm

hi buzzer the key is not 123456 its got its own code and is labeled on the note acceptor theres dil 1to8 on the note acceptor that you have to turn some on then turn machine of to re-set the code then enter the code i also have to turn dil switch 8 on the mpu board as that is the dil that talks to the note acceptor when i turn the machine on after entering the code it come up with c-c talk the coin mech it says sr5i

egan79 · Post by **egan79** » Sat Aug 03, 2013 8:15 pm

on the mpu board i have two sets of bank dil switches 1to8 dill 4 5 and 8 is on all rest are switched off on the note acceptor its self there is dil 1to8 with switches 2 5 7 on there was on when i got the machine cheers

buzzer · Post by **buzzer** » Sat Aug 03, 2013 8:21 pm

switch 2 and 5 off m8 (on note acceptor)

what number are you using for bnv key?

egan79 · Post by **egan79** » Sun Aug 04, 2013 11:39 am

thank you ok so just leave number 7 on the (note acceptor) the number used to enter the bnv i have to turn dil switch 8 on the main board then it allows me to enter the bnv code